Offer

Samba - light design

Description

 

 
Type Samba 160 Samba 200 Samba 240 Samba 280
Working width [m] 1,60 2,00 2,40 2,80
Swath width [m] ~ 1,10 ~ 1,40 ~ 1,70 ~ 2,10
Number of discs [pcs.] 4 5 6 7
Number of knives [pcs.] 8 (4x2) 10 (5x2) 12 (6x2) 14 (7x2)
RPM [rpm./min] 540 540 540 540
Power demand [HP] from 20 from 30 from 45 from 60
Working capacity [ha/h] ~1,5 ~ 2,0 ~ 2,5 ~ 3,0
Weight [kg] 410 450 490 530

 

 


Technical Details

 

2

 

Samba light rear disc mowers with working widths of 1,60 m, 2.00 m, 2.40 m and 2.80 m are designed for farmers who own smaller farms. Application of innovative suspension assembly allows adjusting optimal pressure of cutterbar onto the ground. Mowers feature the recent SaMASZ manufactured LiteCUT light cutterbar with quick knife replacement option. What is more, the mower has been equipped with hardened discs and slides, central knife holder and strengthened bushings. Besides, properly designed hardened knife holder significantly improves cleaning of the bar from any dirt present.
 
5 Advantages of Samba mowers:

- light mower design,
- lower power demand with comparable alternative drum mower,
- design based on the new LiteCUT cutterbar,
- opened rear and front guards significantly facilitate replacement of cutting knives,
- setting mower to transport, operating position and for driving over windrows owing to use of only mower's hydraulic cylinder
       

Intended use


This is a good choice for smaller farms, and for fairly maintained meadows, e.g. of turf type, also for mid-size farms.

       
3

Swath guides


Applied are rotating rubber swath guides resistant to winding up when operating in higher grass.

   

 

 

 

 

 


LiteCUT
LiteCUT cutterbar is another new model of the cutterbar installed in light mowers Samba, designed for operation on smaller farms and on mountainous and swamp areas. Completely new design provides reliability, high durability and precise cutting, and all that with reduced power demand.
       

General advantages of LiteCUT cutterbars:

 

1. Smooth mowing height adjustment from 4 up to 6 cm
2. Cogwheels have 6208 2RS N type bearings, while disc module 6306 2RS C3. These are one of the most durable among used by our West European competition.
3. Owing to their properly shaped surface, specially tampered discs of hardened steel provide protection against cutterbar dirtying.
4. Easily replaceable, bolted knife pins.
5. Tempered central knife holder made of hardened steel. Its enhanced design enables the cutterbar to be cleaned more thoroughly and disables knife locking underneath the disc - loose knife mounting allows for its 360° rotation.

6. Innovative quick knife replacement system.
A knife is replaced by means of a special lever, only when the disc is perpendicular to the cutterbar (± 20°). Thanks to this, probability of „loosing” a knife upon hitting a stone is reduced to minimum.
7. Tampered sliding skids of hardened steel provide protection of the cutterbar surface from the bottom. Easy and quick replacement of sliding skids by unscrewing three bolts.
8. Additional skid of tampered and hardened steel to protect the cutterbar drive.
9. Changed design of drums to improve swath guiding quality, particularly on hills and to reduce risk of grass winding onto the drums.
10. Improved knife overlapping (to reduce the risk of leaving potential strips of uncut grass).
11. Quick and easy module replacement, owing to enhanced upper hub.
12. Cogwheels 18 mm width.
13. 105 mm long knives of high quality meet very strict safety requirements. To guarantee the quality, each of the knives has SaMASZ badge engraved.
14. High resistance to clogging with clay.

 

 

 

 


 

4
Standard-delivered specially designed lever allows quick replacement of cutting knives.

 

 

Folders

 

 

ENG1

   
  DISC MOWERS  
 

pdf_ikona

Document size: 7,5 MB  



 

Gallery